Meeting Room Lighting: Lux, Glare And Layout For Conference Rooms

Nov 14, 2026

Leave a message

A fit-out contractor in Singapore outfitted a 28 square meter meeting room for a fintech office. The original spec called for six basic square panels in two rows. On move-in day the table was usable, but the presenter's side washed out on camera, the window side showed bright streaks, and the projector screen could barely be read with the panels on. The meeting room lighting had been chosen by ceiling count alone, without a lux target, a glare limit, or a separate scene for presentations. The fix was not more fixtures. Good meeting room lighting starts with the table, not the ceiling, and needs a balanced layout plus a dimming scene the control system actually supports.

Lux Targets: What the Table and Screen Side Actually Need

Standard meeting room lighting is planned around the conference table, not the whole ceiling grid. Most office standards call for 300 to 400 lux on the table surface for general meetings; a training or design review room can run to 500 lux. The screen wall is the opposite: it needs lower ambient light, usually 100 to 150 lux, so the image stays readable without washing out. That split is what separates meeting room lighting for discussion from meeting room lighting for presentations.

Start from the room size and the table position. A small huddle room under 15 square meters typically takes two to four panels. A medium room of 15 to 30 square meters needs four to six, and a boardroom over 30 square meters often mixes a main table row with perimeter or linear fixtures. The meeting room lighting should be calculated on the table plane, roughly 0.75 meters above the floor, rather than the ceiling. Ask the supplier for a lux map or fixture count based on room dimensions, ceiling height and reflectance before you lock the order. Plan the light spill to the glass wall and corridor next door in the same calculation.

Glare, Color Temperature and CRI for Conference Use

Glare controls how comfortable attendees feel over a three hour meeting. Any meeting room lighting spec should list a UGR target before it lists a fixture price. Specify UGR below 19 for rooms with screens and computers. A clear diffuser on a cheap panel can push UGR to 25 or higher, which shows up as bright spots at the edge of vision and eye strain by midday. An opal or micro-prism diffuser keeps the source hidden and keeps the rating in the acceptable range.

Color temperature sets the mood. Everyday working meetings suit 4000K, neutral white that keeps people alert without feeling harsh. A boardroom or hospitality-style meeting room can sit at 3000K to 3500K for a warmer look. CRI matters once cameras are involved. Video calls reproduce skin tones and slides more naturally at CRI 90 or above; a CRI 70 fixture leaves faces flat on screen. Specify these numbers on the spec sheet.

Fixture Choice: Panels, Linear Bars and Layout Spacing

Panels are the default for grid ceilings. For a straightforward meeting room lighting layout, they spread light evenly across the table and are the simplest option for a standard office meeting room. You can compare sizes, diffusers and CCT options in our LED panel light range. Linear bars suit long tables, feature ceilings or modern designs; they run parallel to the table toward the presenter. The rectangular linear guide compares linear proportions and mounting styles for those layouts.

Spacing follows the ceiling height and the fixture's light distribution. The meeting room lighting grid should mirror the table shape, not the room rectangle. As a rule, keep fixtures roughly one ceiling height apart so the center and edges of the table get similar illumination. Do not run a single row dead center on a wide table, or the edges fall dark. If the ceiling is concrete or has no grid, the surface mounted linear guide covers flush-mounted options that read clean without a recessed void. Match mounting across the whole room; mixing recessed panels with suspended bars in one space looks unfinished.

Mounting Methods and Ceiling Type

Recessed panels drop into a T-bar or plasterboard ceiling and read flush, with no frame visible. Surface-mounted bars fix directly to concrete or exposed ceilings where a recessed void does not exist. Suspended units hang on wires or rods for high ceilings and long tables. Confirm the void depth, cable entry and load fixings at the drawing stage, because changing a mounting method after production usually means a new housing.

Dimming, Scenes and Control Wiring

A meeting room lighting setup that cannot change scenes fights its own purpose. The meeting room lighting scenes are recalled from the controller, not switched by hand on the breaker. Plan at least two scenes: a presentation scene that dims the table side and keeps the screen wall dark, and a discussion scene that brings the full table up to 300 to 400 lux. A video-call scene may raise the face side slightly and soften the background.

Confirm the dimming protocol before ordering fixtures. 0-10V is common and simple for basic projects. DALI gives individual addressability and scene recall from a room controller, which matters for a suite of meeting rooms. Check that driver, dimmer and control panel speak the same protocol; a dimmable fixture paired with the wrong signal buzzes, flickers, or will not dim to a usable level. Wiring, scene buttons and sensor inputs should be laid out on the lighting drawing, not added after the ceiling goes up.

Quick Answers and the Room Spec Checklist

How many lux does meeting room lighting need? General meetings run 300 to 400 lux on the table. Training or document review rooms can reach 500 lux, while the screen wall stays at 100 to 150 lux.

What UGR should I specify? UGR below 19 for rooms with screens and computers. Use an opal or micro-prism diffuser to keep bare LEDs out of peripheral vision.

Which fixture fits a grid ceiling? Panels are the standard even-light choice. Linear bars suit long tables and feature ceilings, with mounting matched to the ceiling type.

Should the whole room run one brightness? No. Set separate presentation and discussion scenes, and confirm the dimming protocol matches the driver and controller.

Write these lines on the room spec:

  • Room dimensions, ceiling height, table size and reflectance
  • Target lux on the table and a separate screen-wall level
  • UGR limit, color temperature and minimum CRI
  • Fixture type, count, spacing and mounting method
  • Dimming protocol, scenes and control panel layout

For an office fit-out, send the room schedule, ceiling heights and control preference through our inquiry page. We will size the fixture count, layout spacing and scene package before you commit to a batch, so the meeting room lighting works for both the presenter and the camera on day one.

Send Inquiry
Contact us if have any question

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.

Contact now!